操作人員應經常檢查打膠機設備上的氣管、膠管，防止這些管子老化破裂、漏氣，避免這些問題可以增加安全。
　　The operators should regularly check the trachea and hose on the rubber machine equipment to prevent these pipes from aging and cracking and air leakage, so as to avoid these problems to increase safety.
　　雙組份打膠機是從人工到自動化的一個重大轉變。它包含了機械、電氣、PLC程序的編寫等。很好地詮釋了機電一體化技術的非凡應用。是機電一體化朝著智能化、模塊化、綠色化的佳體現。
　　The double component glue machine is a major change from manual to automation. It includes the compilation of mechanical, electrical, PLC programs and so on. It is a good interpretation of the extraordinary application of mechatronics. It is the best embodiment of the mechatronics, the intellectualization, the modularization and the green.
　　在次使用新買的打膠機設備時，要注意檢查設備是否完好無損、有無松動脫落現象。因為打膠機在運輸過程中很可能因受到各種震動而使得機器設備上的各連接處有松動或者脫落，這就需要在檢查完確認沒問題過后才能投入使用。如果出現問題，應及時給予解決方可投入使用。
　　In the first use of new buy rubber machine equipment, pay attention to check whether the equipment is intact, there is no loosening and falling off. Because the rubber machine is likely to be loosened or dropped due to all kinds of vibration during the transportation process, so it is necessary to put into use after checking the confirmation. If there is a problem, the solution should be put into use in time.

　　壓縮空氣送入膠瓶（注射器），將膠壓進與活塞室相連的進給管中，當活塞處于上沖程時，活塞室中填滿膠，當活塞向下推進滴膠針頭時，膠從針嘴壓出。滴出的膠量由活塞下沖的距離決定，可以手工調節，也可以在軟件中控制。
　　Compressed air into the plastic bottle (injector), the rubber pressure into the piston chamber is connected with the feed tube, when the piston is in the up stroke, the piston chamber filled with glue, glue when the piston pushes down the needle, needle from the mouth out of glue. Glue drop out is determined by the distance of the piston down, can be manually adjusted, can also control the software.
　　可提高點膠速度，改善點膠環境，提高點膠質量。通過利用氣壓和以微處理器為基礎的定時裝置來調節涂敷到部件上的流體量，替代了操作員的人為猜測。
　　The adhesive speed can be improved, the adhesive environment is improved, and the quality of the glue can be improved. By using the pressure and microprocessor based timing devices to regulate the amount of fluid applied to the components, the artificial guess is replaced by the operator.
　　在打膠機的使用過程中，要注意不要用手去觸摸該設備上的任何部位，不要去觸摸控制箱內電路板上的元件，尤其禁止帶電插撥，情節嚴重則會導致人身觸電和損壞設備。
　　In the process of using glue machine, we must pay attention not to touch any part of the device with hands, do not touch the components on the circuit board of the box, especially prohibit electrified plugging. If the circumstances are serious, the body will be electrified and damaged.
　　我們用滿腔的熱情、無限的激情對待工作和客戶，我們愿意用勤奮的努力和您一起共鑄美好明天！
　　We are filled with enthusiasm and passion towards work and customers, we are willing to use the hard work and you create a better tomorrow!